Skip to content
Faisal Mahmud TusherDigital marketing, SEO & analytics
with Faisal Tusher

Interactive Tools › Reach & Frequency Calculator

Reach & Frequency Calculator for Retargeting

Using the reach and frequency calculator for retargeting: a small audience of past visitors, frequency that climbs fast, and setting a cap from the curve.
Tutorialintermediate5 min readUpdated

Why retargeting changes the calculator's inputs

Prospecting audiences are large next to the impressions bought, so the calculator's curve is mostly in its steep early section where more impressions mean more people. A Remarketing list sits at the other end. It may hold tens of thousands of people while the budget buys hundreds of thousands of impressions, so the curve is flat almost from the start. Every additional impression lands on someone who has already seen the ad.

That shifts what the calculator is for. The question is no longer how many people the plan will reach, since the answer is close to all of them, but how many times each person will see the ad and whether that number is helping or annoying. The guide to prospecting and remarketing explains why the two need different budgets and caps; this page uses the calculator to put numbers on the remarketing side.

The audience input also needs care. Site analytics may count far more visitors than the platform can match to accounts, and exclusions — recent buyers, existing customers, staff — reduce the list further. The matched size after exclusions is the only one that reflects who can actually be served.

The inputs for retargeting

Calculator inputOn the default pageFor retargetingWhere to find it
Audience sizeAny audience figureThe matched list of recent visitors or engagers after exclusionsPlatform audience size for the list
ImpressionsAny impression countImpressions the retargeting budget buys within the list's windowBudget ÷ CPM × one thousand

The list's membership window matters as much as its size. A list of visitors from the last week turns over quickly; one covering the last few months holds more people but includes many whose interest has faded. Enter impressions for the same period the list covers, so the frequency output describes that window. Prices per thousand impressions on retargeting lists are often higher than on broad audiences because the lists are small and contested; use the price your account has actually paid for similar lists.

Entering the retargeting inputs step by step

  1. Read the matched list size

    Open the audience in the ad platform and take the matched size after all exclusions, not the count of site visitors. Enter it as audience size.

  2. Derive impressions for the list's window

    Take the budget planned for the same number of days the list covers, divide by the expected price per thousand impressions and multiply by one thousand. Enter that as impressions.

  3. Convert the frequency to a weekly figure

    Note the average frequency the calculator returns and divide it by the number of weeks in the window. This weekly figure is the one to compare with response data and caps.

  4. Find the budget that meets the cap

    Lower the impressions until the weekly frequency sits at or below the level your reports suggest is useful. The budget behind those impressions is the ceiling for this list.

A worked retargeting audience with illustrative inputs

Illustrative example — not a real result

A furniture-rental company checks its visitor list

Roomloft Rentals, an invented furniture-rental company, retargets visitors from the last 30 days. Its analytics show about 65,000 visitors in that period, but after matching and excluding current customers the platform list holds 40,000 people. The monthly retargeting budget is $4,800 at an assumed CPM of $8, which buys 600,000 impressions. The calculator shows modelled reach of effectively the whole list and an average frequency of about 15 over the month — around 3.5 exposures a week per person. The company's own reports show conversion rate falling once people see its ads more than about twice a week. Cutting impressions to about 300,000 still reaches almost the whole list at a frequency of about 7.5 a month, close to that level, and frees roughly half the budget.

Reach & Frequency Calculator

Open the Reach & Frequency Calculator →

Prefilled with the example's inputs: Audience size 40,000 · Impressions 600,000 → Estimated reach 40,000 · Reach % 100% · Average frequency 15.

All figures above belong to the invented company, and the CPM is an assumption made for the example. Lower the impressions in the embedded calculator to watch frequency fall while reach barely moves.

Interpreting reach and frequency for retargeting

Read reach % only as a saturation check. On a retargeting list it will usually sit close to the full audience. That is not a success to report; it is confirmation that the budget is large enough to reach everyone and that any further money will buy repetition.

Average Frequency is the output to act on. Divide it by the number of weeks in the list's window to get a weekly figure, because response to retargeting depends on how often people see the ad in a short period rather than over a whole month. Compare that weekly figure with your own data on response by frequency. The frequency and creative fatigue guide describes the signs that repetition has started to hurt: falling click-through, rising cost per result and negative feedback.

Above the frequency at which response falls, there are two remedies. Cut the budget until the curve brings weekly frequency back to a useful level, or widen the list's window so the same impressions spread over more people. Raising budget on a saturated list does the opposite of what is needed.

Splitting the list helps here as well. People who viewed a product page last week and people who browsed the home page two months ago respond to repetition differently, and one blended audience gives them the same exposure. Run the calculator separately for each segment with its own matched size and share of the budget; the warmer segment can usually carry a higher weekly frequency before response falls.

Then use the curve to set the platform cap. Rather than accepting a default, choose the cap from the weekly level where your data shows response flattening, and confirm that the planned impressions can actually be delivered under it. If they cannot, the platform will either underspend or, where caps are soft, overshoot. The frequency glossary entry covers how the measure is defined across platforms.

The calculator cannot tell you whether retargeted conversions are extra sales. Many people on the list would have returned and bought anyway. A holdout group, excluded from retargeting, shows how much of the Reach actually changed behaviour.

Pitfalls when retargeting numbers go into the calculator

  • Planning retargeting like prospecting reach. Setting a reach goal for a list that the budget saturates in days wastes the calculator's main insight. Plan the frequency instead.
  • Using the list size before matching. The visitor count overstates the audience, so frequency comes out far lower than delivery will show.
  • Ignoring that buyers stay in the list unless excluded. Customers who have already bought keep seeing the ad, raising frequency for the rest and spending budget on people who have converted.
  • Raising budget on a saturated list. More money on a fully reached list only multiplies exposures per person. Widen the window or add a new audience before increasing spend.

Frequently asked questions

Which audience size should I use for a retargeting list?

The matched size the platform reports for the list, after exclusions such as recent buyers and existing customers. The number of visitors recorded on your site is usually larger, because not every visitor can be matched to a platform account and some are removed by exclusions. Using the unmatched count makes frequency look lower than it will be.

How do I set a frequency cap for retargeting?

Work out the weekly frequency the budget implies, then look at how response changes with frequency in your own reports. Set the cap near the level where conversion rate or click-through starts to fall, and reduce the budget if the calculator shows the plan delivering more than that cap allows. Avoid relying on a platform default.

Why does retargeting frequency rise so quickly?

Because the audience is small. Once the list is almost fully reached, nearly every extra impression goes to someone who has already seen the ad. Frequency then rises roughly in step with impressions, so doubling the budget roughly doubles how often each person sees the ad rather than finding new people.

Terms used on this page

Tools to try

Where this page is used

Also related

Related